1 000 MW机组给水泵汽轮机轴封系统故障分析及处理

doi:10.3969/j.issn.1008-0198.2022.05.021

湖南电力 ›› 2022, Vol. 42 ›› Issue (5): 119-122.doi: 10.3969/j.issn.1008-0198.2022.05.021

• 故障与分析 • 上一篇

1 000 MW机组给水泵汽轮机轴封系统故障分析及处理

余兴刚^1,2, 魏海峰³, 朱太春³, 郭绪宏⁴, 蒋伯华⁴

1.高效清洁发电技术湖南省重点实验室,湖南长沙 410007;
2.国网湖南省电力有限公司电力科学研究院,湖南长沙 410007;
3.国家能源集团永州发电有限公司,湖南永州 425000;
4.湖南省湘电试验研究院有限公司,湖南长沙 410004

收稿日期:2022-05-09 修回日期:2022-06-02 出版日期:2022-10-25 发布日期:2022-11-16

Fault Analysis and Management of Feedwater Pump Turbine Shaft Sealing System for a 1 000 MW Unit

YU Xinggang^1,2, WEI Haifeng³, ZHU Taichun³, GUO Xuhong⁴, JIANG Bohua⁴

1. Hunan Province Key Laboratory of Efficient & Clean Power Generation Technologies, Changsha 410007, China;
2. State Grid Hunan Electric Power Company Limited Power Research Institute, Changsha 410007, China;
3. China Energy Yongzhou Power Generation Co.,Ltd.,Yongzhou 425000, China;
4. Hunan Xiangdian Test & Research Institute Co.,Ltd., Changsha 410004, China

Received:2022-05-09 Revised:2022-06-02 Online:2022-10-25 Published:2022-11-16

摘要/Abstract

摘要： 某新建燃煤电厂1 000 MW机组采用1台100%锅炉最大连续出力容量的汽动给水泵,调试期间该机组给水泵汽轮机轴封系统出现轴封蒸汽带水和给水泵侧轴封管道异响的故障。通过调整与分析,发现造成上述故障的原因为轴封回汽管道安装方式设计不合理和凝汽器内轴封蒸汽管道套管安装不完善。采取在轴封回汽管道最低点处加装疏水水封筒、在凝汽器内轴封蒸汽管道上加装保温的措施,成功排除了给水泵汽轮机轴封系统的故障。

关键词: 给水泵汽轮机, 轴封系统, 轴封带水, 轴封管道异响

Abstract: A 1 000 MW unit in a newly-built coal-fired power plant adopts a steam-driven feed water pump with a capacity of 100% boiler maximum continuous rating. During commissioning, the shaft seal system of the feed water pump turbine of this unit has the faults of water entrainment of shaft seal steam and abnormal noise of the shaft seal pipe at the side of the feed water pump. Through adjustment and analysis, it is found that the causes of the above-mentioned failures are unreasonable design of shaft seal steam return pipe and imperfect installation of shaft seal steam pipe sleeve in condenser. The fault of shaft seal system of feed water pump turbine has been successfully solved by installing hydrophobic water seal cylinder at the lowest point of shaft seal steam return pipeline and installing heat insulation on shaft seal steam pipeline in condenser.

Key words: feedwater pump turbine, shaft sealing system, shaft seal with water, abnormal sound of shaft seal pipe

余兴刚, 魏海峰, 朱太春, 郭绪宏, 蒋伯华. 1 000 MW机组给水泵汽轮机轴封系统故障分析及处理[J]. 湖南电力, 2022, 42(5): 119-122.

YU Xinggang, WEI Haifeng, ZHU Taichun, GUO Xuhong, JIANG Bohua. Fault Analysis and Management of Feedwater Pump Turbine Shaft Sealing System for a 1 000 MW Unit[J]. Hunan Electric Power, 2022, 42(5): 119-122.

参考文献

[1]冯伟忠.1 000 MW超超临界机组给水泵及系统优化[J]. 中国电力,2010,43(8):26-30.
[2]余丽萍.大型火电站给水泵组的配置与布置分析[J].华电技术,2017,39(12):4-7,73.
[3]陈仲毅,吴志祥.660 MW机组100%容量汽动给水泵项目的技术经济性分析[J].节能,2018,37(2):18-23.
[4]周宇玮,胡奉云.1 000 MW机组单台汽泵的可靠性研究[J].神华科技,2017,15(8):54-57.
[5]余兴刚,李旭,陈非,等.高中压合缸汽轮机过桥汽封内泄漏流动的数值研究[J].汽轮机技术,2017,59(5):365-367,370.
[6]阳欧,高扬.电加热器在超超临界机组轴封系统中的应用[J].汽轮机技术,2021,63(4):246-248.
[7]黄威,刘伟,忻建华.超超临界机组轴封供汽系统参数研究和抱轴问题分析[J].汽轮机技术,2014,56(5):361-363.
[8]杜开榜,童宏仙,刘孝峰.汽封供汽汽源温度匹配的探索和实践[J].热力透平,2021,50(4):281-284,288.
[9]刘俊峰.350 MW超临界机组给水泵汽轮机润滑油进水原因及改造方案[J].中国电力,2015,48(3):6-8,12.
[10]陈思迈.给水泵汽轮机油中带水问题的分析及处理[J]. 汽轮机技术,2007,49(5):392-393.
[11]王印义,张中林.火电机组汽动给水泵组油中带水原因分析及解决方案[J].电站系统工程,2021,37(6):45-47.
[12]何冬辉,叶振起,赵奕州.1 000 MW超超临界汽轮发电机组轴封系统故障分析及处理[J].东北电力技术,2019,40 (5):28-30,55.
[13]张宇翔,边鹏飞,王永锋,等.300 MW汽轮机低压缸轴封供汽系统甩水原因分析及处理[J].内蒙古电力技术,2019,37(2):36-38,43.
[14]张延风,王文强,岳恒.600 MW机组低压轴封供汽管路上绝热罩的加装[J].吉林电力,2018,46(2):54-56.
[15]李阳海,张才稳,王广庭,等.1 000 MW火电机组水击现象分析及预防处置措施[J].汽轮机技术,2015,57(1):75-77.

1 000 MW机组给水泵汽轮机轴封系统故障分析及处理

Fault Analysis and Management of Feedwater Pump Turbine Shaft Sealing System for a 1 000 MW Unit

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价